What This Cover Does
The step fairing handle cover is the trim piece at the passenger-side grab handle area on the VNL step fairing. It closes off the handle mounting pocket, hides the fastener heads and keeps spray, salt and grit out of the recess behind it. It carries no structural load, but it is the first thing a driver's hand and boot touch every shift.
Failure is almost always mechanical or environmental, not electrical. The cover takes a direct hit from boots coming off the step, door-edge contact in tight yards, and constant vibration through the fairing. Add winter chemicals and UV and the black finish chalks out, the clip tangs fatigue, and the corner nearest the step splits.
This part is supplied as a single unit, right-hand passenger side only. The left side is a separate piece. Confirm which side you are holding before you order, because a driver-side cover will not mirror onto the passenger fairing.
Why These Numbers Match
82757807 is the headline number most shops write down, usually copied off a parts diagram or an old invoice. 42529 shows up in the same cross-reference list for the same physical cover in the same RH step fairing handle position on the VNL Gen 3 platform.
Numbers diverge like this for ordinary reasons: supersessions, separate catalog systems, and distributors assigning their own stock numbers to a part that never physically changed. What matters is the hard points — mounting location, clip and fastener pattern, and the opening the cover has to close. Those are the same across both listings, which is why they land on one aftermarket part.
Both numbers are listed here for identification only. PartStop is not affiliated with, endorsed by, or authorized by any OEM. Use the cross-reference as a starting point, then verify against the number stamped on the cover coming off your truck or against the VIN. A cross-reference is not a fitment promise.
Check Before You Order
Pull the old cover and look at it in your hand. Confirm it is the passenger side, confirm the finish is black, and confirm the fastener pattern matches what is on your fairing. If there is a number molded or stamped on the back face, photograph it. That number is better evidence than any catalog lookup.
Inspect what is behind the cover while it is off. If the handle mount, the fairing boss or the captive hardware is cracked or elongated, a new trim cover will not sit flat and will fail again. Replace or repair the mounting point first, then fit the cover using the factory hardware — no drilling or trimming should be required.
82757807 Cross-Reference & Interchange Numbers
These manufacturer and aftermarket numbers commonly cross-reference to 82757807. Use them to identify the part — then confirm the exact fit by VIN or the number stamped on your old unit before you order. An interchange is a starting point, not a fitment guarantee.
| Brand / Line | Cross-Reference Numbers |
|---|---|
| Cross-Reference | 42529 |
Frequently asked questions
Will 42529 fit the same spot as 82757807?
They are listed as cross-references for the same RH step fairing handle cover on the Volvo VNL 2018-2025. The mounting points and the opening are the same, which is why one aftermarket part covers both numbers. Confirm with your VIN or the number on the part you are removing before ordering.
Is this the driver side or passenger side?
Passenger side, right-hand only, at the step fairing handle area. It ships as one unit. The left-hand cover is a different part, so if you need both sides you are ordering two separate pieces.
Do I need to drill or modify anything to install it?
No. It is a direct replacement that lands on the original mounting points and uses the factory hardware. If it will not seat flat, check the fairing boss and the handle mount for cracks or elongated holes before forcing it.
Not sure it fits? We check before you pay.
Run your VIN and we’ll match parts to your exact truck, or call the counter — a person who knows trucks verifies fitment by OEM number before the order ships. No wrong-box returns.
More cross-reference guides
Need the part, not just the reading?
Every part below is a Premium Quality aftermarket Direct Replacement with published OEM cross-reference numbers, a 6+ month warranty and same-business-day shipping from Tacoma, WA. Not sure it fits? Run your VIN — or call and a person who knows trucks will verify fitment before you pay.