What This Wrap Does
The PE13050 is a reinforced rubber sleeve that carries the emergency line, service line, and ABS electrical cable in one bundle between the tractor and trailer. It clips on over the existing lines. No welding, no brackets, no disconnecting glad hands to thread anything through. You open the sleeve, lay the lines in, and close it.
The 12 ft length covers the typical run from the cab-mounted pogo stick or tender spring back to the trailer nose on most heavy duty tractor-trailer setups. Measure your existing run before ordering — sleeper cabs and stretched wheelbases can need more length, and a sleeve that comes up short leaves bare hose rubbing at the worst point.
Material is a UV-stabilized, ozone-resistant rubber compound. It is built to sit exposed year round without going brittle in winter or chalking out under summer sun. The wrap does not carry pressure or current itself — it is protection and routing hardware only, so it does not affect brake system performance one way or the other.
Why These Numbers Cross
PE13050 is our aftermarket reference for this wrap. Tectran 13A1201 and Tectran 169125 are listed here because they describe the same class of part: a 3-in-1 clip-on rubber air hose and cable wrap in the standard 12 ft tractor-trailer length. Same job, same mounting method, same bundle count.
Cable management sleeves cross cleanly because there is very little that varies between them. What matters is the number of lines carried, the internal diameter of the channels, the closure style, and the overall length. When those four line up, the wraps are functionally interchangeable regardless of whose number is stamped on the bag.
Those interchange numbers are printed for identification only. PartStop LLC is not affiliated with, endorsed by, or authorized by any OEM or by Tectran. Use the cross as a starting point, then confirm against the number on your old wrap or against your VIN before you commit.
Checks Before You Order
Pull a tape on the existing run first. Measure from where the wrap starts at the cab-side anchor to where it terminates at the trailer connection, with the tractor and trailer straight. Then add slack for turning. If your measured run exceeds 12 ft, this bundle will leave line exposed and you want a longer sleeve instead.
Second, check what you are actually bundling. This wrap is sized for two air hoses plus one ABS power cord. If your truck runs additional cables or oversized hose, confirm the lines physically fit the channels before ordering. Also inspect the air hoses themselves — if the outer cover is already worn through from chafing, replace the hose, not just the sleeve.
PE13050 Cross-Reference & Interchange Numbers
These manufacturer and aftermarket numbers commonly cross-reference to PE13050. Use them to identify the part — then confirm the exact fit by VIN or the number stamped on your old unit before you order. An interchange is a starting point, not a fitment guarantee.
| Brand / Line | Cross-Reference Numbers |
|---|---|
| Tectran | 13A1201, 169125 |
Frequently asked questions
Do I have to disconnect the air lines to install this?
No. The wrap is a clip-on design, so you lay the existing hoses and cable into the open sleeve and close it around them. No hose disconnection, no special tools, no permanent mounting. That also means you can pull it and move it to another tractor when you swap units.
Is PE13050 the same part as Tectran 13A1201?
They cross as the same type of part — a 3-in-1 clip-on rubber wrap in the standard 12 ft length. We list 13A1201 and 169125 for identification only and are not affiliated with that manufacturer. Verify against the number on the wrap you are replacing, or by VIN, before ordering.
Will a 12 ft wrap cover my sleeper cab setup?
Twelve feet covers typical rear brake, air, and power runs on most heavy duty configurations, but sleeper cabs and long wheelbase tractors can run longer. Measure your existing line run before ordering. If the sleeve falls short, you leave bare hose in the exact spot where chafing usually starts.
Not sure it fits? We check before you pay.
Run your VIN and we’ll match parts to your exact truck, or call the counter — a person who knows trucks verifies fitment by OEM number before the order ships. No wrong-box returns.
More cross-reference guides
Need the part, not just the reading?
Every part below is a Premium Quality aftermarket Direct Replacement with published OEM cross-reference numbers, a 6+ month warranty and same-business-day shipping from Tacoma, WA. Not sure it fits? Run your VIN — or call and a person who knows trucks will verify fitment before you pay.