What You're Actually Buying
This is a hanger set, not the flap itself - two straight arms that hold your mud flap out and down behind the tandem or steer axle. Heavy duty gauge steel, 30" length, with mounting holes spaced at 1-1/8" center to center. That spacing is the whole ballgame - it's what has to line up with your existing bracket or frame holes.
Straight hangers like this show up most on trailers and straight trucks where you don't need the flap to kick out wide, just hang plumb behind the tire. If your old hanger is bent, cracked at the weld, or the holes are stripped out from years of pressure washing and road salt, this is your part.
Why These Numbers Cross
PN3C006CH and PN-3-C-007-CH from Pino Metal Products both reference the same 30" straight, heavy duty, 1-1/8" spacing spec as our PS-BD.01.UN.007. Pino's been making these hanger patterns for decades and a lot of body shops just call them by the Pino number out of habit - the physical part is what matters, not whose stamp is on it.
Where guys get burned is length and spacing. A 30" hanger with 1-1/8" holes will NOT swap in for a 24" or a set with 1-3/4" spacing - the bolts won't reach the bracket. Pull your old hanger and measure the hole centers with a tape, don't eyeball it. If you don't have the old part anymore, check the frame rail or spring hanger bracket itself for the stamped spacing.
Ordering From PartStop
We stock these in Tacoma and if you're local, same-day pickup is normal - call ahead so we pull the right set off the shelf. Ship nationwide too, usually out the door same day if you order before early afternoon.
Comes with the 6+ month warranty. If it shows up and the holes don't line up with your bracket, call us before you start drilling new holes - we'd rather swap it than have you force a fit that's gonna crack again in six months.
PS-BD.01.UN.007 Cross-Reference & Interchange Numbers
These manufacturer and aftermarket numbers commonly cross-reference to PS-BD.01.UN.007. Use them to identify the part — then confirm the exact fit by VIN or the number stamped on your old unit before you order. An interchange is a starting point, not a fitment guarantee.
| Brand / Line | Cross-Reference Numbers |
|---|---|
| OE | PN3C006CH |
| Pino Metal Products | PN-3-C-007-CH |
Frequently asked questions
Does PS-BD.01.UN.007 fit my straight truck's rear mud flaps?
Depends on your bracket spacing, not the truck make. If your factory hanger has 1-1/8" hole centers and you need a 30" straight arm, this fits. Measure your old hanger or the bracket itself before ordering - VIN doesn't tell you mud flap hanger spec, the physical part does.
Is this the same as the Pino PN-3-C-007-CH?
Same spec - 30" straight, heavy duty, 1-1/8" spacing. Pino's a common name in this hanger category so a lot of counters use their number as shorthand, but confirm the dimensions match your old part, not just the brand name.
Can I use this hanger set with a wider or narrower mud flap?
The hanger itself doesn't care about flap width, it's the flap mounting holes on the hanger arm that matter - most standard flaps will bolt on fine. Just make sure the hanger length (30") gets your flap to the right height off the ground for DOT spec, usually within a few inches of the ground unloaded.
Not sure it fits? We check before you pay.
Run your VIN and we’ll match parts to your exact truck, or call the counter — a person who knows trucks verifies fitment by OEM number before the order ships. No wrong-box returns.
More cross-reference guides
Need the part, not just the reading?
Every part below is a Premium Quality aftermarket Direct Replacement with published OEM cross-reference numbers, a 6+ month warranty and same-business-day shipping from Tacoma, WA. Not sure it fits? Run your VIN — or call and a person who knows trucks will verify fitment before you pay.